37.111.1202 INCORPORATION BY REFERENCE (1) For purposes of this subchapter, the Department of Public Health and Human Services adopts and incorporates by reference the following: (a) Department of Environmental Quality Circular DEQ-4, "Montana Standards for Subsurface Wastewater Treatment Systems" (2013 edition), and Circular, DEQ-2 "Design Standards for Public Sewage Systems" (2018 edition), setting forth minimum requirements for the design and preparation of plans and specifications for subsurface wastewater treatment systems. (b) ARM Title 17, chapter 30, subchapter 6, containing surface water quality standards (last amended December 24, 2020). (c) ARM Title 17, chapter 38, subchapters 1 and 2, containing public water supply maximum contaminant levels and requirements (last amended February 14, 2020). (d) ARM Title 17, chapter 36, subchapters 1, 3, 6, and 8 setting forth subdivision review requirements (last amended February 14, 2020). (e) Food and Consumer Safety (FCS) Circular 1, (2016 edition), setting forth standards for non-public water supplies serving licensed establishments. (f) ARM Title 37, chapter 115, subchapter 1 containing swimming pool and spa requirements (last amended May 15, 2020). (g) ARM 24.301.301, setting forth state plumbing code requirements (last amended June 10, 2022). (h) "Manual of Cross-Connection Control" (10th edition), published by the Foundation for Cross-Connection Control and Hydraulic Research, University of Southern California. This publication sets forth standards for backflow and back siphonage prevention devices. (i) American Society of Sanitary Engineering (ASSE) Standard 1001-2021, "Performance Requirements for Atmospheric Type Vacuum Breakers" (ANSI Approved: November 2021). This standard sets forth regulations and requirements for the use of atmospheric type vacuum breakers. These devices provide protection of the potable water supply against pollutants or contaminants that enter the system due to back siphonage through the outlet. (j) ASSE Standard 1003-2020e2, "Performance Requirements for Water Pressure Reducing Valves for Potable Water Distribution Systems" (ANSI Approved: December 2020). This standard sets forth regulations and requirements for water pressure reducing valves for domestic water distribution systems. These devices reduce static and flowing pressures in water distribution systems. Devices covered by this standard are self-contained, direct acting, single diaphragm types. (k) ASSE Standard 1004-2017, "Performance Requirements for Backflow Prevention Requirements for Commercial Dishwashing Machines" (ANSI Approved: January 2017). This standard sets forth regulations and requirements for backflow prevention devices used on potable water supplies connected to commercial dishwashing machines. (l) ASSE Standard 1011-2017, "Performance Requirements for Hose Connection Vacuum Breakers" (ANSI Approved: November 2017). This standard sets forth regulations and requirements for the use of devices designed to be installed on the discharge side of the hose bibb, hydrant, or faucet which is fitted with hose threads. (m) ASSE Standard 1012-2021, "Performance Requirements for Backflow Preventers with an Intermediate Atmospheric Vent" (ANSI Approved: November 2021). This standard sets forth regulations and requirements for devices that have functional capabilities for preventing both back-siphonage and back pressure and which can operate under continuous or intermittent pressure conditions. (n) ASSE Standard 1013-2021, "Performance Requirements for Reduced Pressure Principle Backflow Prevention Assemblies" (ANSI Approved: June 2021). This standard sets forth regulations and requirements for reduced pressure principle backflow prevention assemblies. These devices are designed to operate under continuous pressure conditions. (o) ASSE Standard 1015-2021, "Performance Requirements for Double Check Backflow Prevention Assemblies" (ANSI Approved: June 2021). This standard sets forth regulations and requirements for double check backflow prevention assemblies. These assemblies are designed and constructed to operate under intermittent or continuous pressure conditions. (p) ASSE Standard 1020-2020, "Performance Requirements for Pressure Vacuum Breaker Assemblies" (ANSI Approved: February 2020). This standard sets forth regulations and requirements for vacuum breaker assemblies. These devices are intended for use in both high and low hazard applications. (q) ASSE Standard 1024-2017(R2021), "Performance Requirements for Dual Check Backflow Preventers" (ANSI Approved: June 2021). This standard sets forth regulations and requirements for dual check backflow preventers. The devices covered by this standard are intended to protect the potable water supply from low hazard pollution at residential service lines and individual outlets. (r) ASSE Standard 1047-2021, "Performance Requirements for Reduced Pressure Detector Backflow Prevention Assemblies" (ANSI Approved: June 2021). This standard sets forth regulations and requirements for reduced pressure detector backflow prevention assemblies. These devices are designed to detect low rates of flow up to 2.0 gpm (0.13 L/s) caused by leakage or unauthorized use. (s) ASSE Standard 1048-2021, "Performance Requirements for Double Check Detector Backflow Prevention Assemblies" (ANSI Approved: June 2021). This standard sets forth regulations and requirements for double check detector backflow prevention assemblies. These assemblies are also designed to detect low rates of flow up to 2 gpm (0.13 L/s) caused by leakage or unauthorized use. (t) ASSE Standard 1052-2016 "Performance Requirements for Hose Connection Backflow Preventers" (ANSI Approved: June 2016). This standard sets forth regulations and requirements for hose connection backflow preventers. These devices are designed to be installed on the discharge side of a hose threaded outlet on a potable water system. These two-check devices protect against backflow, due to back siphonage or low-head backpressure, and are field testable to certify protection under the high-hazard conditions present at a hose threaded outlet. (u) ASSE Standard 1053-2019, "Performance Requirements for Dual Check Backflow Preventer Wall Hydrants – Freeze Resistant Type" (ANSI Approved: April 2019). This standard sets forth regulations and requirements for freeze resistant dual check backflow preventer wall hydrants. These devices protect the potable water supply against back siphonage and backpressure without damage to the device due to freezing. (v) ASSE Standard 1056-2013, "Performance Requirements for Spill Resistant Vacuum Breaker Assemblies" (ANSI approved: February 2021). This standard sets forth regulations and requirements for assemblies classified as spill-resistant vacuum breaker assemblies. These assemblies are designed for installation in water systems that are normally under continuous pressure conditions. (w) ASSE Standard 1057-2012, "Performance Requirements for Freeze Resistant Sanitary Yard Hydrant with Backflow Protection" (ANSI Approved: August 2012). This standard sets forth regulations and requirements for assemblies classified as spill-resistant vacuum breaker assemblies. These assemblies are designed for installation in water systems that are normally under continuous pressure conditions. (2) To obtain, or for information on how to obtain, any document or publication incorporated by reference, contact the Department of Public Health and Human Services, Public Health and Safety Division, Communicable Disease Control and Prevention Bureau, 1400 E. Broadway, P.O. Box 202951, Helena, MT 59620-2951, phone: (406) 444-2837. Copies of the ASSE standards referenced under (1)(i) through (1)(w) are available at https://www.asse-plumbing.org/asse/standards/product/current-standards.
History: 50-52-102, MCA; IMP, 50-52-102, MCA; NEW, 2022 MAR p. 1748, Eff. 9/10/22. |